EUR 0,00
(toimituskulut: 0,00)
Seinäkaappi yksiosainen 9U/395mm peltiovi
Tuotenumero: [20421972] | Valmistaja: TRITON | Mallinum: RBA-09-CS4-CAX-A1 | EAN: 8595105034521
Tuotteella ei ole kuvaa - kuvitus näyttää tuotteen kategorian
Ikke på lager
Tuotetta ei ole varastossa. Lisätietoja
Loppuunmyyty
Tuotetta ei ole varastossa.
Toimitusvaihtoehdot - Valitaan kassalla
Bring - Kotiinkuljetus -arkisin.
15,12
EUR
208,38
ilman ALV 166,04
Kokonaishinta sis. toimitus
223,50
Ilmoita minulle, kun tuotetta on jälleen tarjolla varastossa
Tämä toiminto vaatii sisäänkirjautumisen. Luo käyttäjä ja voit käyttää listojamme esim. säännöllisiä ostoksia ja toivelistoja varten
Luo käyttäjä
Kirjaudu
Luo käyttäjä
Kirjaudu
Send på mail
Dimensions RBA-09-CS4-CAX-A1
A = 500 mm
B = 395 mm
C = 516 mm
D = 600 mm
E = 395 mm
R1 = 454 mm
R2 = 420 mm
Colour: grey (RAL7035)
NET weight: 16,1kg
Gross weight: 16,5kg
Maximum load: 30,0kg
Fittings:
- Key - front door 2x
- Screw 6x50 4x
- Washer 6,6 4x
- dowel 10 4x
- Plastic washer 8x
- Floating nut M6 8x
- Screw M6x16 8x
- Dust cap 1x
Material:
- Sheet steel
RBA switchboard
- 19" one-piece wall-mounted switchboard with IP 30 protection
- The switchboard is hung directly on the wall.
- The switchboard includes two sliding vertical rails.
- The construction of the switchboard:
- Compact welded switchboard
- Full-panel door, thanks to massive hinges can be opened at an angle of almost 180°.
- The permissible load for each door is max. 10 kg.
- The minimum thickness of the surface finish is 65 µm.
- The switchboards are designed for the installation of data and telecommunication equipment and its distribution systems.
- Cable entrances covered with breakaway plugs are located at the top and bottom of the rear wall of the cabinet, others are on the top and bottom wall of the cabinet
Operating conditions
- Operating environment:
- Office
- The switchboard is not intended for outdoor installations and for installations in environments that may adversely affect the functionality of the switchboard and installed equipment (e.g., explosive or wet and humid environments)
- Must be protected against:
- mechanical damage
- improper handling
- use other than that for which the enclosure is intended
- Improper handling is in particular:
- overloading (exceeding the maximum recommended load capacity)
- installation of equipment which may adversely affect the operation and function of the switchboard or the installed equipment
- interference with the construction and design of the switchboard
Installation of the switchboard
- This type of switchboard is hung directly on the wall using screws, dowels and washers (included). The spacing of the holes for hanging is marked with "R" on the switchboard diagram.
- To ensure the maximum recommended load capacity, it is essential that the switchboard is fixed to a wall of the appropriate load capacity (brick, concrete or similar) and that the installed load is evenly distributed in the switchboard.
- If the cables pass through one of the cable entries, it is possible to seal it against the ingress of dust by means of a brush plug and to equip it with a plastic protective frame (both included in the switchboard package).
Environmental protection
- All parts are made of recyclable materials and must be disposed of in accordance with the applicable regulations when the enclosure is discarded.
A = 500 mm
B = 395 mm
C = 516 mm
D = 600 mm
E = 395 mm
R1 = 454 mm
R2 = 420 mm
Colour: grey (RAL7035)
NET weight: 16,1kg
Gross weight: 16,5kg
Maximum load: 30,0kg
Fittings:
- Key - front door 2x
- Screw 6x50 4x
- Washer 6,6 4x
- dowel 10 4x
- Plastic washer 8x
- Floating nut M6 8x
- Screw M6x16 8x
- Dust cap 1x
Material:
- Sheet steel
RBA switchboard
- 19" one-piece wall-mounted switchboard with IP 30 protection
- The switchboard is hung directly on the wall.
- The switchboard includes two sliding vertical rails.
- The construction of the switchboard:
- Compact welded switchboard
- Full-panel door, thanks to massive hinges can be opened at an angle of almost 180°.
- The permissible load for each door is max. 10 kg.
- The minimum thickness of the surface finish is 65 µm.
- The switchboards are designed for the installation of data and telecommunication equipment and its distribution systems.
- Cable entrances covered with breakaway plugs are located at the top and bottom of the rear wall of the cabinet, others are on the top and bottom wall of the cabinet
Operating conditions
- Operating environment:
- Office
- The switchboard is not intended for outdoor installations and for installations in environments that may adversely affect the functionality of the switchboard and installed equipment (e.g., explosive or wet and humid environments)
- Must be protected against:
- mechanical damage
- improper handling
- use other than that for which the enclosure is intended
- Improper handling is in particular:
- overloading (exceeding the maximum recommended load capacity)
- installation of equipment which may adversely affect the operation and function of the switchboard or the installed equipment
- interference with the construction and design of the switchboard
Installation of the switchboard
- This type of switchboard is hung directly on the wall using screws, dowels and washers (included). The spacing of the holes for hanging is marked with "R" on the switchboard diagram.
- To ensure the maximum recommended load capacity, it is essential that the switchboard is fixed to a wall of the appropriate load capacity (brick, concrete or similar) and that the installed load is evenly distributed in the switchboard.
- If the cables pass through one of the cable entries, it is possible to seal it against the ingress of dust by means of a brush plug and to equip it with a plastic protective frame (both included in the switchboard package).
Environmental protection
- All parts are made of recyclable materials and must be disposed of in accordance with the applicable regulations when the enclosure is discarded.