EUR 0,00
(toimituskulut: 0,00)
Black Box PP-ST-625MM-6PAK, ST, Beige, Monitila, 6 kpl
Tuotenumero: [4746705] | Valmistaja: Black box | Mallinum: PP-ST-625MM-6PAK
Ikke på lager
Tuotetta ei ole varastossa. Lisätietoja
Loppuunmyyty
Tuotetta ei ole varastossa.
Toimitusvaihtoehdot - Valitaan kassalla
Budbee Laatikko - Nouda valitsemastasi laatikosta!
Ilmainen toimitus
Bring - Toimitus huoltopisteeseen
7,02
Bring - Kotiinkuljetus -arkisin.
10,03
Toimituskulut on laskettu vastaanottajan postinumeron perusteella:00180 - Helsinki Vaihda postinumero
Syötä postinumero toimitusta varten:
EUR
101,67
ilman ALV 81,01
Kokonaishinta sis. toimitus
101,67
Ilmoita minulle, kun tuotetta on jälleen tarjolla varastossa
Tämä toiminto vaatii sisäänkirjautumisen. Luo käyttäjä ja voit käyttää listojamme esim. säännöllisiä ostoksia ja toivelistoja varten
Luo käyttäjä
Kirjaudu
Luo käyttäjä
Kirjaudu
Send på mail
Quick Facts
- Pre-polished ferrules for fast connections in the field.
- Easy assembly with no need for epoxy.
- Fiber can be reseated.
- Factory polishing eliminates loss concerns.
- Meets TIA/EIA 568A performance requirements and TIA/EIA 604 (focis) connector interface specifications.
- Guaranteed for life!
Further Details
This Pre-Polished Fiber Optic Connector can save technicans a ton of time in the field. These connectors are so easy to install, you can do it in a minute! There's no hand polishing. No epoxy!
Proven mechanical splice technology ensures precise fiber alignment. A factory pre-cleaved, factory-polished ferrule couples to the fiber being terminated with precise mechanical alignment. A proprietary index-matching gel ensures a low loss termination to 62.5-micron multimode optical fibers. There are no expensive tools, no messy epoxy needed.
A factory-installed wedge clip holds the clamping device open while the fiber is inserted. This clip also enables the use of a Visible Fault Identifier (VFI) to provide a "pass/fail" signal once physical contact is achieved. The connector is compatible with 250-µm and 900-µm optical fibers.
This connector is also available in SC and LC versions and for 62.5-micron multimode and single-mode fiber, as well as for OM3 laser-optimized multimode fiber. Connectors for each fiber type are color coded to industry standard requirements to help with identification during and after installation.
- Pre-polished ferrules for fast connections in the field.
- Easy assembly with no need for epoxy.
- Fiber can be reseated.
- Factory polishing eliminates loss concerns.
- Meets TIA/EIA 568A performance requirements and TIA/EIA 604 (focis) connector interface specifications.
- Guaranteed for life!
Further Details
This Pre-Polished Fiber Optic Connector can save technicans a ton of time in the field. These connectors are so easy to install, you can do it in a minute! There's no hand polishing. No epoxy!
Proven mechanical splice technology ensures precise fiber alignment. A factory pre-cleaved, factory-polished ferrule couples to the fiber being terminated with precise mechanical alignment. A proprietary index-matching gel ensures a low loss termination to 62.5-micron multimode optical fibers. There are no expensive tools, no messy epoxy needed.
A factory-installed wedge clip holds the clamping device open while the fiber is inserted. This clip also enables the use of a Visible Fault Identifier (VFI) to provide a "pass/fail" signal once physical contact is achieved. The connector is compatible with 250-µm and 900-µm optical fibers.
This connector is also available in SC and LC versions and for 62.5-micron multimode and single-mode fiber, as well as for OM3 laser-optimized multimode fiber. Connectors for each fiber type are color coded to industry standard requirements to help with identification during and after installation.